Additive Inn
Get instant quote

What is foam board, and when is it good enough for a model?

Foam board is a foam core between paper faces. Its thicknesses and sizes, how to cut it by hand, and when a model needs wood, card or a 3D print instead.

By Terry Tan
On this page

How many pieces from one foam board sheet?

Enter your piece size and quantity, and pick the sheet you can buy.

Layout is a simple grid with 5 mm between pieces; a cutter may fit a few more.

Foam board is a sheet of polystyrene foam with a paper face on each side. It is light and flat and cuts with a knife, which is why it fills study models and display boards. We do not laser cut it. When a model has to last or has to be exact, we cut wood or card on our laser, or 3D print it.

Foam board by job

JobFoam board?If not, we would use
Mounting a print or posterYes, it is lightNot needed
A quick study modelYes, a knife and a steel ruler do itLaser cut card, for a neater one
A model a client will handleOnly if handled gently, because the core is softLaser cut plywood, or a 3D print
A model with exact, repeating detailNot the best choiceLaser cut plywood or acrylic, to plus or minus 0.1 mm
A model that must lastNot the best choice, the core is softA 3D print, or laser cut plywood

Tell us what the model is for

What foam board is

Foam board, also called foamcore, is a board of polystyrene foam clad with paper on both sides, typically white clay-coated paper or brown kraft paper. It is used to mount photographic prints, back picture frames, build scale models and paint on. It is also common for architectural models, prototypes of small objects and patterns for casting.

The first white board was made in 1961 by Monsanto under the name Fome-Cor, in two thicknesses: 1/8 and 3/16 inch, which is 3.2 and 4.8 mm. Acid-free versions exist for framing, and some boards have a plastic face in place of paper.

A warning on names: the word foamboard is also used for PVC foam sheet, a plastic board sold as Forex and Palight. That is a different material. We cover it in our PVC foam board guide.

Thicknesses and sizes

  • 3 mm and 5 mm are the thicknesses we found. The University of Liverpool’s art store, for one, sells A1 sheets in 3 mm and 5 mm.
  • Sizes are often quoted as paper sizes. A1 is 594 by 841 mm, A2 is 420 by 594 mm and A3 is 297 by 420 mm.
  • One print shop works in 5 mm. In Singapore, Gogoprint prints foam board posters in A3, A2 and A1 on 5 mm board.
  • Stock varies by shop. Call before you go, and ask for a sheet of each thickness.

How to cut it cleanly by hand

A sharp craft or utility knife and a metal ruler do all of it. The steps below follow Build a Head’s guide.

  1. Mark the line and lay the board on a cutting mat. Hold a metal ruler on the line.
  2. Make a light first pass. Do not try to cut through in one go: forcing a deep cut crushes the foam.
  3. Repeat the cut two to four more times along the same track.
  4. Keep the blade upright. A knife that leans sideways between passes carves chunks out of the core and leaves a fuzzy edge.
  5. Change the blade the moment it drags, needs force or leaves ragged paper.

A new blade prevents jagged edges, tearing and crushed foam.

Rather have the model made for you? See our scale models

Laser cut card: a neater study model

We do not laser cut foam board. Card is on our laser. It cuts cleanly and fine detail holds, so it is a quick, low-cost way to study a design before committing to timber or acrylic. Card comes in many weights, so tell us the weight and we confirm before anything runs.

For a model to be handled and shown, step up to the next two options.

Send us your card cut file

Laser cut plywood: when it must be exact

Our laser cuts plywood and MDF from 3 mm to 12 mm and holds plus or minus 0.1 mm. It carries the model work we do: baseboards, floor plates, facade panels and fretwork. In the block of flats below, the timber was left raw so it reads as the building itself.

A plywood block of flats cut open to show every floor, beside a red, green and grey frame with three yellow platforms
A block of flats laser cut from plywood, cut open to show its floors. See the project

The limits: laser cutting makes flat parts from sheet, so curved and solid forms are not its job. Our guides to MDF board and plywood types help you pick the sheet.

Send us your plywood model drawings

3D print: when it must last

A printed model has plastic walls, not paper and foam. For a courtyard building, we split the site into sections that fit our printers, printed each in white and joined them on the base. Another model was printed level by level, with clear acrylic columns between the floors.

A white colonnaded building model side on at table level, with the arched pavilion in the middle
A courtyard building, printed in white sections. See the project
A white three-storey building model with open floors, planted terraces and a tree on the upper deck
Three storeys printed level by level. See the project

The limit is time. Most models take 2 to 6 weeks and each is quoted per project, so foam board wins when you need something by tomorrow. Our guide to how scale models are made walks through the stages.

Upload a 3D file and see the price

Where these facts come from

Every outside fact on this page was read on the source’s own website on 19 November 2026. Stock and sizes change, so check the shop before you travel.

Frequently asked

Is foam board the same as foam core or foamboard?

Yes, for the paper-faced kind: foamcore, foam board and paper-faced foam board are one product. The word foamboard is also used for PVC foam sheet, which is a different, plastic-faced material.

What is the difference between 3 mm and 5 mm foam board?

Thickness. Both are a foam core between paper faces. A university art store lists both, and one Singapore print shop works in 5 mm. Buy a sheet of each and test a scrap before you cut the model.

How big is an A1 sheet of foam board?

594 by 841 mm. A2 is 420 by 594 mm and A3 is 297 by 420 mm. Check the shop's own listing for the exact size before you buy.

Can foam board be laser cut?

Not by us. We do not laser cut foam board, the paper-faced kind. Our laser does cut card, plywood, MDF, acrylic and EVA and PE foam. If you want a laser cut study model, card is the sheet to ask for.

Why does my foam board edge look torn?

Usually a dull blade or one deep pass. A sharp new blade, a light first pass and two to four more along the same line help keep the paper face clean and the foam uncrushed.

Can I use foam board for a model that will travel or be handled?

Only if it is handled gently, because the core is soft. For an exhibition model or one a client will pick up, we build in plywood or acrylic, or 3D print it.

Can you print on foam board?

Not through our print studio, which prints on acrylic. A Singapore print shop such as Gogoprint prints posters on foam board. Ask us if you want a printed piece made in acrylic instead.

What can I use foam board for besides models?

Mounting photographs and posters, backing for picture framing, painting, and bouncing light as a reflector in photography.

Chat with us