How do you get 3D printed miniatures that paint well?
3D printed miniatures: how figure scales are named, why resin suits them, where supports leave marks, priming, file licences and home printing.
How tall is a person at each miniature scale?
Enter a height and see it at the common scales.
1:50 means the model is 50 times smaller than the real thing. Bars share one scale so you can compare.
Miniatures are small enough that detail is the whole job, which is why we print them in resin. Stereolithography (SLA) resin printing cures liquid resin with light, and Formlabs, a maker of resin printers, says it gives the sharpest details and smoothest surface finishes of all 3D printing technologies. Below: how miniature sizes are named, where supports leave marks, how to prime, what a download’s licence allows, and whether to print at home.
Miniature scales at a glance
For human figures, the usual way to give a scale is a height in millimetres, not a ratio. The ratio follows from the height, if the figure stands for a man 1.78 m tall.
| If you play or build | Ask for this figure height | About what ratio |
|---|---|---|
| A 28 mm game such as Bolt Action | 28 mm | 1:64 |
| A game that asks for 25 mm figures | 25 mm (1 inch is 25.4 mm) | About 1:72 |
| A large figure | 54 mm or 90 mm | 1:32 or 1:20 |
| A small figure | 15 mm or 6 mm | 1:120 or 1:300 |
| A grid game such as D&D | Whatever your group uses | Each grid square is 5 feet |
Makers measure differently. Some measure to the crown of the head, others to the eyes, and a “28 mm” figure can stand 30 mm. Wikipedia notes that Warhammer 40,000 officially has no scale.
Why resin suits miniatures
A miniature has to show a face, a hand and a weapon at the size of a thumb. Our resin printing builds in layers 0.08 to 0.1 mm thick, which keeps those small shapes sharp.
Our coin-sized princess shows it. The umbrella ribs, the rope belt and the strands of the headdress all held in the resin print, before any paint went on.

The limits are in the handling. Resin prints are washed, dried and cured before they are done, and the liquid is sticky and has to be handled with care. Formlabs says to wear gloves whenever you handle liquid resin or unwashed parts. That is why a service suits many people better than a bench at home.
Supports: where the marks land
A resin print hangs from supports, thin posts that hold overhangs up while the layers build. Each one leaves a small mark where it touched.
Our tabletop miniatures were printed on a lattice of supports, tilted to carry their overhangs. Afterwards the supports come off. Formlabs’ own advice is to sand the remaining support marks for a clean finish.
- The mark sits where the support touched. Tilting the figure moves those spots.
- Tell us the front. A person checks every file before it prints. Say which side matters most and ask how the print would be tilted.
- No promise of zero marks. On a fine, awkward pose, a mark may land near detail and need extra sanding.

Priming and painting basics
A primer is a coat put on before painting, and it gives the paint a better grip on the surface. On a resin print the order is simple:
- Take the supports off and sand the marks.
- Prime the whole figure.
- Paint the figure and its base by hand.
- Seal it.
The paladin on our project page was printed in grey resin, primed, and painted by hand to its design. Painting every side matters: the cape and back are seen too.

Not everyone wants ours painted. We also hand miniatures over clean, with the supports off, ready for your own brush. Our painting and finishes guide covers prep in more depth.
Files and licences
Most miniatures start as a download. A file’s licence says what you may do with it. Under the Creative Commons licences, a licence with NC in its name allows only noncommercial use, so printing copies to sell is out.
Sites that sell files set their own terms, and those can differ. Read them before you send us a file. A person checks every file for printing faults, but the right to use it is yours to confirm. Our guide to free 3D files lists where to look and how to read the licence.
Print at home or have them printed
| At home | Through us | |
|---|---|---|
| Resin handling | You wash, dry and cure the print yourself | We wash, cure and take the supports off |
| Mess and handling | Sticky resin; gloves, and a safety data sheet to read | Not in your home |
| Painting | Your own | Your own, or painted by us by hand |
| Cost | The printer, resin and washing kit | Priced by part weight: see pricing |
A home printer is worth it if you will print most weeks and enjoy the bench work. For one or two special pieces, send the file. Our home printer guide covers that choice.
Small models that are not figures
“Miniature” also means a product shrunk to a desk. We printed a 30 mm armoured vehicle in grey resin, with its roof rails, ladders and turret gun printed in one piece. We also printed four baby walker designs in white, each in one piece, for design review.

If you want a figure of yourself or a pet, that is a Mini Me, not a gaming miniature. See custom figurines.
Where these facts come from
Outside facts were read on 19 November 2026. What Additive Inn prints and paints is from our own project and service pages.
- Wikipedia, Miniature wargaming: how figure size is quoted, the ratios for each height (its table assumes a 1.78 m man and gives rough ratios), measuring to the crown or the eyes, oversized models and Warhammer 40,000.
- Formlabs, What is SLA 3D printing: what SLA is, its detail and surface claim, support removal and sanding.
- Wikipedia, Stereolithography: washing, drying and curing, and sticky resin.
- Formlabs, Resin safety FAQ: gloves for liquid resin and unwashed parts, and checking the safety data sheet for ventilation.
- Wikipedia, Primer (paint): what a primer does.
- Creative Commons, About CC licences: what NC means (noncommercial: not primarily intended for commercial advantage or monetary compensation).
- D&D Beyond, Basic Rules: Playing the Game: the grid square, when you play on a grid.
- Our own pages: coin-sized princess miniature, resin tabletop miniatures, painted paladin, miniature vehicle models, baby walker models and resin printing.
Frequently asked
Is 28 mm the height of the figure or its scale?
It is the height. For human figures, wargamers quote size as a height in millimetres, and the ratio follows from it: 28 mm is about 1:64, if the figure stands for a man 1.78 m tall. Makers measure differently, so ask whether the height is taken to the crown or to the eyes.
Why does a 28 mm miniature sometimes measure 30 mm?
Some makers build models a little oversized so they look more imposing and carry more detail. A figure sold for 28 mm games can stand 30 mm. If your figure has to stand beside others, measure the real ones first.
Are D&D miniatures a fixed size?
The basic rules say that if you play on a square grid, each square represents 5 feet. Ask your group what figure height and base it uses before you print.
Can you print a miniature from a file I downloaded?
Often yes, if the licence allows it. A licence with NC in its name allows only noncommercial use, so do not order prints to sell. A person checks the file for printing faults, but you are the one who must have the right to use it.
Will resin supports leave marks on my miniature?
Supports leave small marks where they touched, and the marks are sanded before painting. Tell us which side is the front and ask how the print would be tilted. We cannot promise zero marks on a fine, awkward pose.
Do the miniatures come painted?
Either way. We paint by hand, down to the scenic base, or hand the miniature over clean with the supports off, ready for you to paint. Say which you want when you ask for a price.
Is it safe to print resin miniatures at home?
It needs care. Resin is sticky and messy. Formlabs says to wear gloves whenever you handle liquid resin or unwashed parts, and to check the safety data sheet for your resin to see what ventilation it needs. Read that sheet before you start.
Can you make a miniature of me or my pet?
Yes, as a Mini Me: you send photos and approve the artwork and a 3D preview, then we print it, and hand-paint it in the painted styles. It is a stylised figure, not a gaming-scale miniature, and it is priced by size in the studio.








