Which material should your custom coasters be made from?
Custom coasters in cork, slate, wood, acrylic or 3D printed plastic: how each is marked, how it copes with a wet glass, and which we make.
What would my own coaster look like?
Drop in a logo or a photo, or type a few words, and see it on each of the two coasters we make.
Drop a logo or a photo here
or tap to choose one. JPG, PNG or WebP.
Showing a sample drawn in code. Change the words or drop your own picture.
Your picture never leaves your device: it is drawn in this page and nothing is uploaded. The preview is a guide, and plastic and ink colours look a little different on every screen. 100 mm is the size the guide uses; ask us for another.
Custom coasters are made in cork, slate, wood, acrylic or 3D printed plastic, and the material decides how your design is marked and how the coaster copes with a wet glass. Our UV print studio prints full colour on acrylic from your artwork, so a coaster-sized piece is an order you can place there, and we make a two-part 3D printed coaster. We do not list cork, slate or wood coasters.
Coaster materials compared
| Material | How the design is marked | Water | Good for |
|---|---|---|---|
| Cork | Laser engraved: a very dark mark | Sources disagree on whether it soaks up water | A soft pad. We do not list it |
| Slate | Laser engraved: a lighter mark on dark stone | Roofing slate takes up under 0.4% water | A rustic, stone look. We do not list it |
| Wood | Laser engraved: darker brown, each piece a little different | Needs sealing, says one guide | A warm look. We do not list it |
| Acrylic | UV printed in full colour (ours) | Plain acrylic takes up at most 0.3 to 0.4% water; no test of the printed face | Logos and photos in colour |
| 3D printed plastic | Colour from the plastic, logo in the lattice (ours) | No water figure for our plastics: ask us | A two-colour coaster in your colours |
A coaster is something to rest a drink on. It protects a table from the condensation on a cold glass, and can stop a hot drink burning the surface. The first ones were stands for sliding wine decanters along a dining table, in common use after about 1760. A German printing company made the first cardboard coaster in 1880.
Cork: a soft pad
Cork is the bark of the cork oak, and its cells are filled with a gas like air, so it behaves like a pad that springs back after pressing. Wikipedia calls cork impermeable, while a coaster guide calls it highly absorbent. Ask whoever sells it which they mean.
A laser marks cork very dark, almost black. It is soft, so too much power chars it and can make it brittle. We do not list cork coasters. If you have a blank, ask us whether we can engrave it.
Slate: stone you engrave
Slate is a fine-grained rock that splits into thin, flat slabs, and roofing slate has a water absorption index under 0.4%, so a slate coaster barely takes up water from a wet glass. A laser fractures the dark top surface and shows the lighter grey stone beneath, so the mark is pale on dark. A laser maker’s own slate coaster project uses plates of about 10 x 10 cm.
We do not list slate coasters. Ask us if you want to know whether we can engrave one you supply.
Wood: warm, but seal it
Wood marks a darker brown, sitting in the grain, and no two pieces mark quite alike. Our guide to laser engraving shows how each material looks. A coaster guide warns that an unsealed wooden coaster is quickly ruined by the condensation from a cold drink, with water stains and warping, and says wood needs a sealant such as polyurethane, lacquer or oil.
We do not list wood coasters either. If you want one, ask what we can engrave.
Acrylic: full colour from your artwork
Acrylic is where a full-colour logo, a pattern or a photo looks best. In our UV print studio we cut white, clear or black acrylic along your artwork’s outline or to a rectangle, and UV print it. The thicknesses are 1.5, 3, 5 and 10 mm. On clear acrylic you can print on the back, so the colour is read through the sheet. The size bands run up to 50 x 50 mm, 100 x 100 mm, A5 and A4 (210 x 297 mm), and the size is the cut piece’s, border included. The 100 x 100 mm band holds a 10 x 10 cm piece, the plate size in that slate project.
Plain acrylic (PMMA) takes up at most 0.3 to 0.4% of its weight in water, says Wikipedia. It is more prone to scratching than glass, and scratches can often be polished out. We have no heat figure for our acrylic sheet, no water test of the printed face and no wear test: ask us if it will sit under a freshly poured hot drink or on a busy bar.
A coaster is not a listed product in the studio. Choose the size and outline, and tell us in the notes it is a coaster, or ask us first.
3D printed: a two-part coaster
Our own coaster is printed in two parts: a black base with a raised rim, and a red lattice top that carries our logo and presses into the base. The two parts print separately, so each takes its own colour.

We have also printed sets carrying a name.

The honest limits:
- Heat. Our heat guide puts PLA’s softening point at about 55°C, PETG’s at about 68°C and ASA’s at about 90°C. For a hot mug, ask us which plastic to use.
- Water. We have published no water test for our coasters, so ask us how yours will be used.
- The surface. A print has fine layer lines, which you can see in the photos.
Sets, sizes and gifts
Pick the size first. One laser maker’s slate project uses plates of about 10 x 10 cm, and the studio’s 100 x 100 mm band covers that. A set is several pieces, and the UV studio takes up to 100 pieces in one job. For a printed set, send the count and the logo.
Coasters are an old way to carry a name. Wikipedia notes they are often printed with a brand, and can promote a drinking establishment, a business or a special event. See door gift ideas for more flat gifts, and our corporate gifts service for a bigger run. For how UV ink works, read what UV printing is.
We have not published a coaster box or a set price. For a boxed gift, tell us the count and the date.
Where these facts come from
Every outside detail was read on the source’s own page on 19/11/2026. A laser maker’s guide sells its own tools, so read its numbers as examples.
- Wikipedia, Drink coaster: what a coaster protects against, its history and its materials.
- Wikipedia, Cork (material), Slate and Poly(methyl methacrylate): cork’s structure and water behaviour, slate’s water absorption, and acrylic’s water absorption and scratching.
- X-Creation, A beginner’s guide to crafting laser engraved coasters: how a laser marks cork, wood and slate, and sealing wood. A laser maker’s guide.
- Trotec, Slate coaster: the slate plate size of about 10 x 10 cm.
- What we cut, print and make is from our own pages: the two-part coaster project, the UV print studio, our guides to laser engraving and heat.
Frequently asked
What are coasters usually made of?
Paperboard is the common one, and tissue paper layers, soapstone, metal, wood and silicone are used too. Cork and bamboo ones appear on the same page. We make ours in acrylic and in 3D printed plastic.
Which coaster material is best for a wet glass?
It depends on what you want it to do. Roofing slate and plain acrylic take up very little water, wood needs sealing, and sources disagree about cork. None of that tells you how a printed face copes with a wet glass. For a hot mug, ask about heat before you choose a plastic.
How big is a coaster?
One laser maker's slate coaster project uses plates of about 10 x 10 cm. Our UV print studio has size bands up to 50 x 50 mm, 100 x 100 mm, A5 and A4, so the 100 x 100 mm band covers that.
Can a coaster carry a full-colour logo?
Yes, on acrylic. We UV print full colour on white, clear or black acrylic, cut to your artwork's outline or to a rectangle. A printed two-part coaster takes its colours from the plastic instead.
Can you engrave my own wood or cork coasters?
Ask us first. Our engraving marks wood a darker brown, but we have not published an engraving service for cork or slate blanks. Send a photo of the coaster and the design.
Can I order a set of coasters?
Yes, for the printed ones. A UV job takes up to 100 pieces. Tell us the count, and ask us about a box if it is a gift.
Does acrylic scratch?
Plain acrylic is more prone to scratching than glass, says Wikipedia, and scratches can often be polished out. We have not tested our printed face for wear, so ask us before it goes on a busy bar.
Do coasters protect a table from heat?
They can. Wikipedia says coasters can stop hot drinks burning a table surface as well as protecting it from condensation. How much a plastic coaster can take depends on the plastic, so tell us what it will sit under.
Can a business put its logo on coasters?
Yes. Wikipedia notes that coasters are often printed with a brand or an advertisement. We print logos on acrylic and into our two-part printed coasters. See our corporate gifts page for a bigger order.








