Additive Inn
Get instant quote

What kinds of acrylic photo frame are there, and what photo do you need?

Acrylic photo frames by kind: a photo printed on acrylic, magnetic blocks, slide-in frames and standing panels, with sizes and the resolution to send.

By Terry Tan
On this page

Is your photo sharp enough to print?

Pick a photo and a size. Nothing is uploaded: the check runs on your device.

Print size

Good from 300 pixels per inch at the printed size, ok from 200, low below that: the same rating our print studio gives. Your file stays on your device.

An acrylic photo frame is one of four things: a photo printed on a panel of acrylic, a block that holds a print between two clear panels, a slide-in frame, or a standing panel. Blocks and slide-in frames hold a print you already have. A printed panel is the photo itself, so the file matters: aim for 300 pixels per inch at the size you want.

Acrylic photo frames at a glance

KindHow the photo is heldWhat you needOur advice
Photo printed on acrylicPrinted on the panel, on the back if it is clearA sharp file, 300 pixels per inch at print sizeWe make it, up to A4 online
Magnetic block frameA paper print between two thick clear panels, held by magnetsA thin print, 550 micron at most in one supplier’s blocksBuy it ready-made
Slide-in frameA print slides into a slot at the sideA print the size of the slotBuy it ready-made
Standing panel or standeeA printed panel in a frame or a slot in a baseA sharp file, a PNG if cut to shapeWe make it, ask about the base
Wall panelA printed panel on holes, standoffs or tapeA sharp fileWe make it, rectangles only for holes

Photo printed on acrylic

This is the kind we make. We cut the acrylic and UV print the photo straight onto it in full colour. On clear acrylic we can print on the back, so the photo is read through the sheet. That gives a glossy look with depth, like a print under glass.

Close-up of a full-colour cartoon cake printed on clear acrylic, with the curve of a black frame along its edge
A full-colour print on A5 clear acrylic. See the project

The studio cuts white, clear or black acrylic in 1.5, 3, 5 or 10 mm, from 5 mm a side up to A4. You can have the cut follow the picture’s outline with a border of clear acrylic round it, 2, 5 or 10 mm wide, so none of the photo is trimmed.

  • Pick it when the photo is the gift and you want it to look finished.
  • Limit: it is only as sharp as your file. A person checks every file before it prints, and tells you if anything will not reproduce.

Upload your photo and see the price

How sharp does the photo need to be?

The studio rates a photo by its pixels per inch at the size you print: good from 300, ok from 200, and low below that. An inch is 25.4 mm, so here is what each size needs:

Print sizeGood: 300 pixels per inchOk: 200 pixels per inch
A6 (105 × 148 mm)1240 × 1748 pixels827 × 1165 pixels
A5 (148 × 210 mm)1748 × 2480 pixels1165 × 1654 pixels
A4 (210 × 297 mm)2480 × 3508 pixels1654 × 2339 pixels

Count the pixels after you crop. A photo of one face cut out of a group shot is much smaller than the original. We take PNG, JPG, SVG and PDF files up to 10 MB.

Not sure if your photo is big enough? Send it

Magnetic block frames

A magnetic block is two thick clear panels with a printed sheet between them. One UK supplier makes its blocks with two 10 mm panels from A7 to A5 and two 15 mm panels at A4, with magnets built in. The photo fills the block edge to edge.

  • Pick it for a counter or a shelf, where a photo should look like a slab of glass.
  • Limit: the panels have to touch for the magnets to hold, so the print must be thin. That supplier says 550 micron at most, about half a millimetre.

Blocks are not on our list, so buying one ready-made is the simpler route. Ask us if you want something similar.

Other stands? See the acrylic stand guide

Slide-in frames

A slide-in frame has a slot at one edge. You slip the photo in, and swap it when you like. One UK supplier sells its single-sided holders this way.

The one we made is a prototype for JCDecaux: a desk frame, shaped like their advertising panel, with 3 mm gloss black acrylic faces, 0.8 mm clear acrylic windows and two 1.2 mm slots, one for a Polaroid and one for a message card. A latch at the base opens so they can be taken out.

A gloss black acrylic desk frame with a clear window and the JCDecaux logo in white below it, lying on tissue paper
The JCDecaux prototype: a slide-in frame for a Polaroid. See the project
  • Pick it when you will change the photo.
  • Limit: the print is paper, so it is only as tidy as the print. A slot cut to a Polaroid does not take other sizes.

Want a frame in your own shape? Tell us

Standing panels and standees

A printed panel can stand in a base. Our Arc Series birthday plaque is an A5 clear acrylic panel with the artwork UV printed on it, held at the top and along the curved base by a black 3D printed frame, so it stands on a desk or a shelf.

A printed clear acrylic panel at three-quarters view, its top edge held in a slot in a black frame that curves down into an angled foot
The frame holds the A5 panel at the top and along its base. See the project

A standee goes a step further: the photo is cut round the person and slots into a base. Our acrylic stand guide shows a wedding photo made this way.

  • Pick it for a desk or a shelf.
  • Limit: the frame or base is part of the order, so tell us the height you want and where it will sit.

Describe the piece and the photo

Hanging it on a wall

A rectangular piece can be made three ways for a wall:

  • Holes for your own screws.
  • Holes and standoffs. A silver standoff goes in each hole and holds the piece a little off the wall.
  • 3M removable tape. It comes packed loose for you to stick on.

Holes are for rectangles only, at least 60 × 20 mm. A piece cut round the shape of a person may have no corner of acrylic to drill.

Choose your mounting in the studio

As a gift

A proof comes first, so the person giving it sees the cut and the print before anything is made. Check the names and dates on it as carefully as you would on a card.

For ideas by occasion, see our guides to birthday gifts and wedding gifts. To see the clear sheet we print on, read our acrylic sheet guide.

Where these facts come from

Every outside fact was read on the page named below on 19 November 2026. The block sizes and the 550 micron limit are one supplier’s, not a standard.

  • UKPOS, magnetic photo block: panel thicknesses, magnets, sizes and the insert limit.
  • UKPOS, free standing single sided acrylic poster holder: slide-in holders.
  • Wikipedia, ISO 216 and Inch: the A4, A5 and A6 sheet sizes and 25.4 mm to the inch, for the pixel sizes.
  • First-party facts (the studio’s sizes, thicknesses, back printing, cuts, mounting, file rules and rating; the Arc Series and JCDecaux projects) are from our own studio and project pages, listed in the facts file for this post.

Frequently asked

Can you print my photo on acrylic?

Yes. Send a JPG or PNG up to 10 MB and choose a size from 5 mm up to A4 in the studio. A proof comes first, so you see the cut and the print before anything is made.

What resolution does a photo need to print on acrylic?

Aim for 300 pixels per inch at the size you print. For A5 that is about 1748 by 2480 pixels. The studio rates a file good from 300, ok from 200 and low below that, so a small photo is a warning, not a surprise.

How do I find out how many pixels my photo has?

Open the file's details on your phone or computer: they usually list its width and height in pixels. Send the original file, not a screenshot or a copy that may have been shrunk on the way.

What is a magnetic acrylic photo block?

Two thick clear acrylic panels with magnets built in, holding a printed sheet between them. One UK supplier's blocks run from A7 to A4, and the sheet must be thin, 550 micron at most, so the panels can touch.

Can an acrylic photo hang on a wall?

Yes. A rectangular piece can have holes for your own screws, or holes with standoffs that hold it a little way off the wall, or 3M removable tape. Holes are for rectangles only.

Can the photo be cut to the shape of the person?

Yes. Send a PNG with a see-through background and the acrylic is cut round the shape, with a border of 2, 5 or 10 mm of clear acrylic that you choose. A JPG is cut as a rectangle.

Can you make a frame that holds a Polaroid?

We designed and made one prototype for JCDecaux, with two 1.2 mm slots for a Polaroid and a message card. It is not a stock item, so ask us if you want something similar.

How long does a printed acrylic photo take?

A proof comes first, and the piece is ready 5 to 7 working days after you approve it. If you need it for a date, tell us the date when you ask.

Chat with us