How is a custom acrylic keychain made, and what do you send us?
How a custom acrylic keychain is made in Singapore: artwork printed on acrylic and cut to shape, sheet colours, ring options, what to send.
On this page
- Acrylic keychain choices at a glance
- Printed in colour, cut round the art
- Front print or back print
- White, clear or black acrylic
- Thickness and the ring tab
- Rings, chains and clasps
- Epoxy dome: ask us first
- What artwork to send
- One keychain or a hundred
- Other keychains we make
- Where these facts come from
- Frequently asked
Will your artwork make a good keychain?
Pick your PNG and the keychain's size. Nothing is uploaded: the check runs on your device.
Longest side
Good from 300 pixels per inch at the printed size, ok from 200, low below that: the same rating our print studio gives. Your file stays on your device.
A custom acrylic keychain is a small plate of acrylic with your artwork printed on it, cut to the outline of the art, with a tab and a hole for the ring. We make ours by printing the artwork with ultraviolet (UV) light-cured ink and laser cutting the acrylic around it. Below: the choices that change how it looks, the file to send, and how a batch is counted.
Acrylic keychain choices at a glance
| Choice | What you get | Our verdict |
|---|---|---|
| Print on the front | Colour printed right on the face | Works on white, clear or black acrylic |
| Print on the back | Read through the clear sheet, glossy, with depth, like a print under glass | Clear acrylic only |
| White, clear or black acrylic | Solid white, see-through, or solid black | The three sheets in our print studio |
| Glitter acrylic | Sparkle in the sheet | Not in the studio: ask us |
| Mirror acrylic | A gold or silver mirror face | Not in the studio: ask us |
| Thickness | 1.5, 3, 5 or 10 mm | 1.5 mm or 3 mm for a keychain |
| Shape | Cut round your art, with a border of 2, 5 or 10 mm | Needs a PNG with a transparent background |
| Art on both faces | Different print on front and back | Not in the studio: ask us |
| Epoxy dome | A thick clear resin layer over the print | Not in our listings: ask us |
Printed in colour, cut round the art
UV printing hardens the ink with ultraviolet light as it lands, so full-colour artwork goes straight onto the acrylic. The laser cuts along the outline of your artwork, so the plate takes your shape instead of a plain rectangle.
For a private client we made 12 keychains of their chicken rice artwork, about 10 cm across. Each was cut to the round plate of the artwork, printed in full colour, and given a small tab at the top for the ring.


One catch. Our online print studio draws the cut from your artwork, but its holes are for screws at the corners of a rectangle, not for a ring. A keychain with a ring tab goes through us: send the artwork and say where the ring goes.
Front print or back print
A front print sits on the surface and looks crisp. On clear acrylic you can print the back instead. The artwork is printed mirrored and read through the sheet, which looks glossy, with depth, like a print under glass.
What to know:
- Back printing works on clear acrylic only. White and black are always printed on the front.
- The studio prints one face of a piece. For art on both faces, ask us first.
White, clear or black acrylic
White acrylic is solid white, so colours stand out. Clear is see-through, like glass. Black is solid black and prints in white or colour.
Ink is slightly see-through, so on black or clear acrylic a layer of white ink goes down first and the colours go on top. That is why a logo stays bright on a dark keychain.
Glitter and mirror sheets are not in the studio. If you want one, ask us, and read our guides to acrylic sheet and mirror acrylic first.
Thickness and the ring tab
The studio cuts acrylic at 1.5, 3, 5 or 10 mm. It describes 1.5 mm as thin and light, 5 mm as sturdy for signs and 10 mm as chunky, for awards. For a keychain that hangs from a bag or a key bunch, start at 1.5 mm or 3 mm.
Keep the ring hole away from the edge. ACRYLITE, a maker of acrylic sheet, says the centre of a fastening hole should sit at least 1.5 times the hole’s width from the edge. The rule is written for bolted fastening holes, not key rings, so it is only a guide. On our chicken rice keychains the ring hole sits in a tab above the art.
Rings, chains and clasps
A keyring, also called a split ring, is a ring, typically metal, that holds keys and small items. A key ring came with every keychain in our chicken rice set.
Other hardware is a different job:
- Ball chain is small metal balls joined by short wire. It swivels without kinking but has relatively low strength.
- A lobster clasp is held closed by a spring. You open it with a small lever.
We have not listed either as a standard fitting. Ask us which one suits your tab.
Epoxy dome: ask us first
An epoxy dome is a thick, clear layer of resin on top of a printed face. The chicken rice keychains above have no dome, and our print studio does not list one. If a dome is what you want, ask us and we say plainly whether we can do it.
What artwork to send
Send a PNG with a transparent background. PNG is the format to choose when transparency matters, and our studio finds the cut line from that transparency. A JPG, or a PDF page, has no see-through edge, so it is cut as a rectangle.
- Size: a PNG or JPG at 300 dpi at the printed size. A vector file (SVG or PDF) is fine too.
- Limits: up to 10 MB a file in the studio.
- A check: a person checks every file before it prints, and flags anything that will not run clean.
One keychain or a hundred
The studio takes from one piece up to 100 in one job. A batch is counted in a way that helps you:
- Set-up is paid once per order. The file, the laser job and the print set-up do not repeat for each piece.
- Each extra piece costs less than the first. The laser cuts the whole order in one run, with the pieces fitted across one sheet, so cutting per piece falls as the count rises.
Prices are by size and quantity: see pricing or the studio’s own price.

Other keychains we make
- Engraved black acrylic: 55 by 20 mm, engraved on one side, from 30 pieces. Each can carry its own portrait or name. See custom keychains.
- One engraved keychain: a brushed steel plate on leather, engraved on both sides. The engraving shop takes single pieces.
- 3D printed: colour goes into the plastic, and the shape can be anything you draw.
- Cast brass: in 2022 we made 80 brushed brass team keychains, engraved on the back. Ask us if you want brass.


Where these facts come from
What Additive Inn makes is from our own pages: the UV print studio’s catalogue, the custom keychains service and the chicken rice project. Everything about the world was read on 19 November 2026.
- Poly(methyl methacrylate), Wikipedia: PMMA and its trade names.
- Image file type guide, MDN Web Docs: PNG and transparency.
- How far in should I drill a hole from the edge of acrylic sheet?, ACRYLITE: hole to edge distance.
- Keychain, Ball chain and Lobster clasp, Wikipedia: what the hardware is.
- Doming for Domed Labels, Hoenle: what a dome coating is.
Frequently asked
Can a photo go on an acrylic keychain?
Yes, a photo prints in full colour. A JPG is cut as a rectangle, though. For a cut that follows the shape of what is in the picture, send a PNG with a transparent background.
How big can a custom acrylic keychain be?
The largest piece our UV print studio takes is A4, which is far bigger than a keychain needs. The chicken rice set above is about 10 cm across, with the ring tab on top.
Is Plexiglas the same as acrylic?
Plexiglas is a trade name for the same plastic, polymethyl methacrylate (PMMA), which is commonly called acrylic. Perspex and Acrylite are other trade names for it.
Can every keychain carry a different picture or name?
Yes for our engraved keychains: send the photos, or a spreadsheet with one row per person. For printed acrylic keychains with a different picture on each, ask us before you order.
Do you supply the ring?
A key ring came with every keychain in the chicken rice set. Tell us if you want a ball chain or a clasp instead, and we confirm what we can fit.
Why does the ring go through a tab and not a hole in the artwork?
ACRYLITE's rule for bolted fastening holes in its sheet is a centre at least 1.5 times the hole's width from the edge, so a 4 mm hole wants its centre 6 mm in. A key ring is not a bolt, so treat it as a guide. On the chicken rice keychains the hole sits in a tab above the art, clear of the picture.
Can an acrylic keychain glow in the dark?
We do not list glow acrylic. The glow-in-the-dark keychains we have made are 3D printed name tags, with the names and rims in glow material from the printer.
How long does a printed acrylic keychain take?
Our UV printing pages put a normal-size job at 5 to 7 working days from a confirmed quote. A big batch takes longer, so give us your date first.








