Scuba gear display stands for CMP Technologies
Slatwall displays made to fit CMP Technologies' regulators, masks and fins: bent steel stands with 3D printed holders, in place of off-the-shelf hooks.
- Client
- CMP Technologies
- Hangs on
- CMP's existing slatwall, with no new fittings
- Made for
- Regulators, dive masks and fins
- Colours
- Matt black and Isuzu Blue
- Steel displays: 8 for regulators, 10 for masks, 10 for fins
- 28
- Regulator holders, 3D printed in carbon-fibre PETG
- 33
- Holder designs tried on the real regulators
- 5
What we brought
What we can do
We design around your actual products
We measured CMP's own regulators, masks and fins, and tried every printed holder on the real gear.
How we look after you
You see it before we make it
CMP reviewed the drawings, a steel prototype and five holder designs on the way to the final order.
What you get
One look across your whole wall
Steel displays in matt black and Isuzu Blue, with printed holders, for every piece of gear on show.
Gallery
The whole project at a glance. Drag or swipe to browse; tap a picture to enlarge it.
1 / 41
-
The finished piece
-
The regulator display and its steel frame.
-
The hose loops through the slot.
-
The whole panel, from the front.
-
The second stage, held flat on the panel.
-
The first stage and the hose loop.
-
From above the panel.
-
The second stage, close.
-
From the left.
-
From low on the right.
-
The whole display at an angle.
-
A fin on its stand.
-
The fin stand holds it at an angle.
-
Side on, the fin hangs from its stand.
-
The foot pocket rests on the legs.
-
The fin from behind.
-
From the toe end.
-
Where the blade meets the legs.
-
Foot pocket up.
-
The stand alone.
-
From low down.
-
Side on, the other side.
-
From above.
-
Design and prototyping · First designRenderThe regulator panel and its lift-off hook.
-
RenderThe mask shelf, 298 mm wide.
-
RenderThe fin stand, 462 mm tall.
-
Design and prototyping · Holder testsA test holder tried on a regulator.
-
Fitting holders to both ends of the hose.
-
A test holder on the hose, up close.
-
Design and prototyping · Steel prototypeThe bare steel prototype with test holders.
-
A second regulator on the prototype.
-
The prototype's frame, from bench height.
-
Design and prototyping · Holder designs A to EHolders A and B on a sample panel.
-
Holders C and D.
-
Holder E cradling the hose.
-
ProductionA fin stand, ready for the wall.
-
The fin stand's two legs, from the front.
-
The slatwall hook, bent from the same sheet.
-
The fin stand, side on.
-
Build and assemblyThe spare regulator, held in place.
-
The acrylic plate beside the mouthpiece.
The build
How we built it
5 steps, from the brief to the finished piece. Pick a step to jump to it.
The brief
Step 1 of 5 · 23/02/2026
- Mounting
- Their standard slatwall, hung like the old hooks
- Gear
- Regulators, dive masks and fins
- Quantity
- Eight to ten sets, one look across the range
At Additive Inn, our 3D printing studio in Singapore, we designed display stands for CMP Technologies, a company in the scuba diving trade. Their slatwall used off-the-shelf hooks; they wanted stands made for their regulators, masks and fins.
Design and prototyping
Step 2 of 5 · 06/03/2026
We measured CMP's own gear and drew three folded steel displays: a sloped regulator panel 446 mm wide that lifts off the slatwall to release, a 298 mm mask shelf and a 462 mm fin stand set at 105°.
-
First design
The regulator panel and its lift-off hook.
Render +2 more
-
Holder tests · 10/03/2026
We tried printed holders on CMP's regulators by hand, to see how each part should sit.
Photo +2 more
-
Steel prototype · 25/03/2026
A bent steel panel with printed holders, the hoses looping through its slot.
Photo +2 more
-
Holder designs A to E · 31/03/2026
Five holder shapes, A to E, tried on a painted sample panel before production.
Photo +2 more
Production
Step 3 of 5 · 31/03/2026
CMP ordered the approved design. The displays were cut and bent from mild steel: 8 for regulators, 10 for masks and 10 for fins. We 3D printed the 33 regulator holders in black carbon-fibre PETG.
Build and assembly
Step 4 of 5
The displays were finished in matt black and Isuzu Blue. We fitted the holders with magnets and stainless steel hardware, and added a clear acrylic plate for product details.
The final build
Step 5 of 5 · 09/04/2026
CMP's regulators, masks and fins now hang on displays made for them, in one look across the range. The regulator panel lifts off the slatwall, and the holders keep each part in place.
More product development
See all product development →-
Danial Custom dragon shoe attachments A pair of gold dragon heads for Danial's trainers, sculpted in 3D, test-fitted on the shoe, printed in resin and screwed to each heel. -
3D printed alarm clock stand for the Google Nest Mini Our own design: an orange 3D printed stand that turns a Google Nest Mini smart speaker into a classic twin-bell alarm clock.