3D printed mushroom lamp
A red and white mushroom table lamp of our own design, 3D printed in a batch, with glowing spots and our name on every stem.
- Service
- Industrial 3D Printing
- What it is
- A table lamp we designed ourselves
- How it is made
- FDM 3D printing, in batches
- Lights up in
- White, warm yellow and blue
What we brought
What we can do
Light through the spots
The white spots let more light through than the red cap, so each lamp glows in a spotted pattern.
How we look after you
Our name on every stem
ADDITIVE INN stands raised on every stem, printed in one with the part, with no label to peel.
What you get
A batch that matches
We printed the lamps as one batch, so the caps, spots and stems match from one lamp to the next.
Gallery
The whole project at a glance. Drag or swipe to browse; tap a picture to enlarge it.
1 / 43
-
The finished piece
-
A finished lamp in daylight.
-
A finished lamp glowing in the dark.
-
Lamps glowing warm yellow and blue.
-
Lit white, the spots glowing through.
-
Four lamps lit on the grass.
-
The stem glows too, name and all.
-
Unlit, in daylight.
-
Up close among the plants.
-
Our name on the stem, in daylight.
-
Lit white behind the succulents.
-
The spots glowing white.
-
Cap and stem both glowing.
-
Lit against a pale wall.
-
The glowing cap, up close.
-
From the side, lit.
-
Bright spots on the red cap.
-
A step back, still lit.
-
Glowing in a dim room.
-
Lit from inside as the room dims.
-
Warm yellow in front, blue behind.
-
The warm stem, name and all.
-
A tray of lamps in a dim room.
-
On the grass, blue and warm.
-
Warm white in front of the blue.
-
Blue on the left, warm on the right.
-
Four lamps from a little higher.
-
Spots bright on the front lamp.
-
The group from a step back.
-
The name glowing on the grass.
-
ProductionFive lamps from the batch in a row.
-
Three lamps from the batch, unlit.
-
Two from the batch, one up on the bench.
-
Three from the batch, nearest on the left.
-
Three from the batch, nearest on the right.
-
The same three, a step back.
-
Low on the grass with three lamps.
-
Five lamps in a row.
-
Down the row, front lamp in focus.
-
Every cap matches the next.
-
The row from the front.
-
FittingThe cap seated on its stem.
-
Our name raised on the stem.
The build
How we built it
4 steps, from the brief to the finished piece. Pick a step to jump to it.
The brief
Step 1 of 4
- Cap
- Red, with white spots and gills underneath
- Stem
- White, with ADDITIVE INN raised near the base
- Light
- Inside the lamp, glowing through the cap and stem
At Additive Inn, our 3D printing studio in Singapore, we designed our own mushroom table lamp. We set out to make a red cap that glows through white spots, with our name on the stem, in a design that prints the same every time.
Production
Step 2 of 4
We 3D printed each lamp as two parts, a red cap set with white spots and a white stem, and ran them as a batch so every lamp matches the next.
Fitting
Step 3 of 4
We fitted the light inside each lamp and seated the cap on its stem.
The final build
Step 4 of 4
The finished lamps glow through the red cap, the white spots and the stem, in white, warm yellow or blue, ready for a shelf, a desk or a display.
More production runs
See all production runs →-
QuantumTX SLA printed bars, painted to Pantone 300C A repeat order of 20 blue bars for a device made by QuantumTX: SLA printed, sanded and spray-painted to Pantone 300C, with the colour approved on a sample bar first. -
RVM Systems Laser-cut acrylic cover panels for RVM Systems Twenty 3 mm matte black acrylic panels that cover an opening in RVM Systems' machine, drawn up from the client's sketch and laser cut once a sample had been tried.